Understanding Plumber's Essentials When Installing a Bathtub
Understanding Plumber's Essentials When Installing a Bathtub
Blog Article
In this article below you can get some decent additional info all about A Step-by-Step Guide to Installing a Bathtub.
:max_bytes(150000):strip_icc()/convert-tub-to-shower-4156975-05-db9a69eb718545759045e6e39b4cfacf.jpg)
Mounting a tub isn't exactly brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling abilities. Changing an old tub with a new one is likewise a reasonably tough job. If the old bathtub is conveniently available, the task can relocate easily; if you need to open a wall surface to remove the old tub and place the new tub, the task is much harder. In either situation, the job is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub and set in the new one. Make certain you have certified yourself for the work and also are comfortable trying it. Rather than working with a contractor to take over a halfway-completed task, it is better to consider utilizing one before you start. Possibilities are you may require a professional plumber to make tube links.
This short article will aid you install a new tub in your restroom if you have actually already acquired a brand-new bathtub and do not need to transform the arrangement of your previous water supply pipelines.
Your tools and also material checklist need to make up the following:
Planning for the Setup
To start with, the sustaining framework provided with the bathroom needs to be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the faucet includes a plastic washer, it is fitted in between the bath and the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps device to avoid stress on the tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the electrical outlet through the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you make use of every one of the supplied washing machines.
Link the catch to the bottom of the waste outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its last position.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you must do is separate the water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The procedure of eliminating the existing taps can be rather bothersome as a result of the restricted access that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a fabric all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have actually been removed, utilize the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning throughout this process. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned of any type of old securing compound.
Before proceeding to fit the brand-new taps, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the new taps to fit.
Setting up the Bathtub
Using both wood boards under its feet, position the bathtub in the needed position. The wooden boards are useful in equally spreading the weight of the bathtub over the location of the boards instead of focusing all the weight onto 4 small points.
The next goal is to ensure that the tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the tub till the spirit level reviews level.
To mount taps, fit all-time low of the furthest adaptable faucet adapter to the ideal supply pipeline by making a compression join; after that do the same for the other faucet.
Activate the supply of water as well as check all joints and also new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise check the overflow electrical outlet and the typical electrical outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the producer's instruction manual. Tiling and sealing around the bath tub should wait till the tub has actually been used at least when as this will settle it into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will certainly need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the mounting opening in the bath/basin making certain that the washing machines remain in location between the tap and also the sink. Safeguard the tap in position with the supplier offered backnut. When the faucet is safely in position, the supply pipes can be attached to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with typical tap ports. The previous type must be attached to the tap finishes first, tightening just by hand. The supply pipelines can later on be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the location where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture a stiff seal, causing the water to pass through the wall between the bath and also the tiling, bring about complications with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your components as well as fittings. They are marketed in tubes as well as cartridges, as well as are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to permit the movement experienced when the bathtub is in use. The sealer can break relatively very early if you do not take into consideration this activity prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are likewise quickly readily available on the marketplace. It is recommended to fit the ceramic tiles utilizing waterproof or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed our section about Tools You Need to Install a New Bathtub . Thanks so much for spending some time to read through our content. Those who appreciated our blog post kindly remember to share it. I love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Ready anytime, dial! Report this page